manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 99

Action

Command

Check information about the
observing port.

display observe-port

Check information about port
mirroring.

display port-mirroring

Check the configuration of flow
mirroring in the traffic policy on
an interface.

display traffic policy interface

 [ 

interface-type

interface-number

 ] [ 

inbound

 ]

 

If the following results are obtained, the configuration succeeds:

l

The number of the observing port is configured properly.

l

The type of the observing port is configured properly.

l

The RSPAN VLAN is configured properly.

l

A proper traffic policy is applied to the interface where incoming flows need to be
monitored.

l

The traffic policy contains a proper traffic classifier and a traffic behavior, and the traffic
behavior contains the flow mirroring action.

7.13 Canceling Flow Mirroring

This section describes how to cancel flow mirroring.

7.13.1 Establishing the Configuration Task

Applicable Environment

When flow mirroring is enabled and the flow, with the same attributes, passing through the
S5700 does not need to be monitored, you can cancel flow mirroring.

Pre-configuration Tasks

None.

Data Preparation

To cancel flow mirroring, you need the following data.

No.

Data

1

Type and number of the interface where flow mirroring needs to be cancelled

2

Name of the traffic policy

 

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

7 Mirroring

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

90

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands