manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 13

Figure 1-1

 Basic process of Auto-Config

No

Obtain a configuration 

file

Timer expires, delete 

temporary 

configuration and 

make configuration 

file effective

End

Does the 

device need to be 

upgraded?

Start a timer to set the 

delay in device restart

Can a 

patch file be 

downloaded to 

device?

Obtain a version file

Obtain the patch file

Is the 

version file 

obtained?

Is the patch 

file obtained?

No

Yes

Is there patch file 

information?

No

No

No

Yes

Yes

Yes

Yes

Is the version file 

valid?

Restart device

Is the patch file 

valid?

Obtain the Web file

Is the 

configuration file 

obtained?

Yes

Is there Web 

file information?

Yes

Set the restart flag

Yes

Yes

Specify it as next 

startup file

Specify it as next 

startup file

Start a new 

AutoConfig process

Is the restart

flag 1?

No

Yes

No

No

No

No

No

Send DHCP Request 

packets periodically

Auto-Config starts

No

Stop sending DHCP 

Request packets

Yes

No

Yes

Configure non-

authentication for VTYs

Allocate IP address

Parse Option 

parameters

Are 

DHCP Reply Packets

received?

Are 

DHCP Reply packets 

valid?

Are there 

Version file name and 

version info?

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

1 Auto-Config

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

4

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands