manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 122

Power Supply Combination

Available PoE Power

250 W constant current

250 W constant current

246.4W

250 W constant current

500 W constant current

369.6W

500 W constant current

500 W constant current

369.6W

 

8.3 Configuring PoE Functions

This section describes how to configure PoE functions.

8.3.1 Establishing the Configuration Task

Applicable Environment

The S5700 can detect whether a device connected to it needs the remote power supply and
provide power for the device that requires the remote power supply.

According to the actual requirements on the network, you can:

l

Set the maximum power and reserved power of the PoE power supply on the S5700 through
commands.

l

Control the remote power supply features of PoE interfaces separately, for example, enable
or disable the remote power supply function, and set the maximum output power, the power
supply mode, and the power supply priority through commands.

Pre-configuration Tasks

Before configuring the PoE functions, complete the following task:

Installing the PoE power supply on the S5700.

8.3.2 Configuring the PoE Function Globally

Procedure

l

(Optional) Setting the maximum output power of the device.
1.

Run:

system-view

The system view is displayed.

2.

Run:

poe max-power

 

maximum-power

 [ 

slot

 

slot-id

 ] 

The maximum output power of a board is set.

The value of 

maximum-power

 ranges from 15400 to 739200, in mW.

l

(Optional) Configuring the PoE power supply management mode
1.

Run:

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

8 PoE Configuration

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

113

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands