Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 32 / 138

2.3.2 Power Module

Appearance

Figure 2-9 Power module

(1) Positioning lock

(2) Running indicator (3) Alarm indicator

(4) Fault indicator

(5) Ready switch

(6) Output port

(7) Input port

Table 2-2 Indicator description

Indicator

Color

Status

Description

Running

indicator

Green

Steady

The system is working in inverter mode.

Blinking

at long

interval

● The inverter is ready and in standby state

(blinking at 0.5 Hz, on for 1s and off for

1s).

● The inverter is not started (blinking at 0.2

Hz, on for 2.5s and off for 2.5s).

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

2 Overview

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands