Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 29 / 138

Figure 2-6 UPS conceptual diagram in maintenance bypass mode

2.2.2.5 ECO Mode

The economic control operation (ECO) mode is an economical working mode,

which can be configured on the LCD or web user interface (WebUI). In ECO mode,

when the bypass input is within the ECO voltage and frequency ranges and other

ECO power supply conditions are met, the UPS works in bypass mode and the

inverter is in standby state. When the bypass source voltage is outside the ECO

voltage range, the UPS transfers from bypass mode to inverter mode. In bypass

mode or normal mode, the rectifier keeps working and charges batteries using a

charger. The ECO mode delivers a high efficiency.

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

2 Overview

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands