Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 106 / 138

NO TICE

After the inverter starts, the UPS still works in bypass mode and the inverter is on

standby. If the bypass is not normal, the inverter supplies power immediately. If

the inverter is not started, the UPS may be disconnected.

Figure 4-7 System status in ECO mode

----End

4.6 Testing Batteries

4.6.1 Lead-Acid Battery Test

4.6.1.1 Forced Equalized Charging Test

Context

NO TICE

Before a forced equalized charging test, ensure that:
● The mains input is normal.
● Batteries are properly connected.
● Batteries are not in the equalized charging state.

Procedure

Step 1 On the home screen of the LCD, choose System Info > Maintenance > Battery

Maint.

Step 2 Tap Start next to Forced Equalized Charging to start a forced equalized charging

test.

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

4 Operations

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands