Huawei TP3206 Installation Manual Download Page 155

Page: 155 / 200

HUAWEI TP3206&TP3218&TP3218S Telepresence

Installation Guide

12 Installing the Front Panel

Issue 05 (2014-08-01)

Huawei Proprietary and Confidential

150

Figure 12-4

Mounting the upper center front panel segment (C2)

----End

Mounting Side Front Panel Segments (C5 and C6)

The mounting method is the same for the leftmost and rightmost front panel segments. The

following procedure uses the leftmost front panel segment as an example.

To facilitate mounting, slightly open the side rear panel segments.

Step 1

Place the hole on the right side of the leftmost front panel segment (C5) onto the dowel pin on

the left triangle front panel support (A9), as shown in

Figure 12-5

Summary of Contents for TP3206









































































































































































































Search results

Summary of Contents for TP3206

Reviews:

Related manuals for TP3206

Brands by name

Popular brands

Huawei TP3206, Installation Manual

Search results

Summary of Contents for TP3206

Reviews:

Related manuals for TP3206

Brands by name

Popular brands