Huawei TP3206 Installation Manual Download Page 105

Page: 105 / 200

HUAWEI TP3206&TP3218&TP3218S Telepresence

Installation Guide

9 Installing Devices

Issue 05 (2014-08-01)

Huawei Proprietary and Confidential

100

Figure 9-8

Splicing HD display screens

Adjust the left and right HD display bases until the three HD displays are on the same

plane.

Adjust the left and right HD displays until the three HD displays are perpendicular to the

horizontal plane.

Step 2

Measure the distances between the left and right HD displays and the ground, as shown in

Figure 9-9

. Ensure that the distance difference is not greater than 3 mm. If the distance

difference is greater than 3 mm, adjust the HD display bases to address this issue.

Summary of Contents for TP3206









































































































































































































Search results

Summary of Contents for TP3206

Reviews:

Related manuals for TP3206

Brands by name

Popular brands

Huawei TP3206, Installation Manual

Search results

Summary of Contents for TP3206

Reviews:

Related manuals for TP3206

Brands by name

Popular brands