Huawei TP3106 Commissioning Manual Download Page 27

Page: 27 / 202

Table 2-6

IP settings

Parameter

Value

Remarks

Connection type

Static IP

Fixed value.

Local IP address

10.11.250.61

In this field, enter the center
telepresence codec's external
IP address.

Subnet mask

255.255.255.0

In this field, enter the center
telepresence codec's external
subnet mask.

Gateway address

10.11.56.1

In this field, enter the center
telepresence codec's gateway
IP address.

Alternate IP address

172.16.21.61

In this field, enter the center
telepresence codec's internal
IP address.

Alternate subnet mask

255.255.255.0

In this field, enter the center
telepresence codec's internal
subnet mask.

DNS server address

Network interface mode

Auto detection

Fixed value.

100 Mbps, full duplex

Standard value for Huawei
internal network

Step 5

Local IP address

and

Alternate IP address

, respectively enter the external and internal IP

addresses assigned to the telepresence codec (the IP address in the preceding figure is for your
reference only). Select

Auto detection

for

Network interface mode

and click

Save

Step 6

Repeat the preceding steps to set the IP addresses of the other two telepresence codecs.

----End

2.6.3 Setting the Telepresence Host IP Addresses

Step 1

Connect a computer directly to the telepresence host. Change the computer's IP address to be in
the same network segment of the telepresence host's external IP address (192.168.1.1), as shown
in

Figure 2-14

HUAWEI TP3106&TP3118&TP3118S
Commissioning Guide

2 Deployment Preparation

Issue 01 (2015-02-12)

Huawei Proprietary and Confidential

Summary of Contents for TP3106











































































































































































































Search results

Summary of Contents for TP3106

Reviews:

Related manuals for TP3106

Brands by name

Popular brands

Huawei TP3106, Commissioning Manual

Search results

Summary of Contents for TP3106

Reviews:

Related manuals for TP3106

Brands by name

Popular brands