Huawei TE80 Administrator'S Manual Download Page 52

Page: 52 / 178

HUAWEI TE80 Videoconferencing Endpoint
Administrator Guide

4 Display Device and Camera

Issue 02 (2014-03-30)

Huawei Proprietary and Confidential

Parameter

Description

Setting

position

on the screen.

This parameter is available only when

Automatic layout mode

is set to

PiP

NOTE

Only the main output port supports this
parameter.

right corner

Display local
video

Display remote
video

Display
Presentation

Specify the content to be display through
a port.

You can select these three parameters for
video output ports, except Main output
interface and Auxiliary output port.

Choose whether to display
the local and remote videos
and presentations based on
your needs.

Step 4

Select

Save

----End

4.2.2 Adjusting the Picture Offset

If you find that the displayed video deviates from its normal position, adjust the picture offset.

Prerequisites

A VGA or YPbPr video signal source is connected to the endpoint.

Background

VGA or YPbPr Image offset may occur in video input or output, such as when the computer
desktop is displayed on the display.

Procedure

Step 1

Choose

Advanced

Settings

Video

Image Offset

Step 2

Select a video input or output port.

You can adjust the picture offset only for a video input or output port to which a VGA or YPbPr video
signal source is connected. The ports to which other video signal sources are connected are unavailable
for adjustment.

Step 3

Select

Horizontal offset

Vertical offset

and move the slider to make adjustments.

----End

4.2.3 Adjusting the Sampling Phase

If a blurring or slight jitter issue occurs in the video shown on the display device, adjust the
sampling phase.

Summary of Contents for TE80



















































































































































































Search results

Summary of Contents for TE80

Reviews:

Related manuals for TE80

Brands by name

Popular brands

Huawei TE80, Administrator'S Manual

Search results

Summary of Contents for TE80

Reviews:

Related manuals for TE80

Brands by name

Popular brands