Huawei TE30 User Manual Download Page 124 | Manualshive

Page: 124 / 157

background image

l

If a call is set up successfully, the communication cable works properly for the call mode
used.

l

If a call cannot be set up, verify that the cables are connected correctly and securely and
the communication parameters are set correctly. If the problem persists, contact the
videoconferencing network administrator to check the network.

13.1.3 Viewing System Status

Knowing system status at any given time helps to better maintain the TE30.

Use any of the following methods to access the

Status

screen and view system status:

l

Press on the remote control and select

Status

.

l

Select

from the option bar.

l

Choose

Advanced Settings

>

Diagnostics

>

Status

.

The following information is displayed on the

Status

screen:

l

Line status: includes the IP address, GK status, site number, SIP information, and running
duration

l

Call status: includes the line rate, video rate (frame rate), presentation rate (frame rate),
audio rate, video packet loss rate, presentation packet loss rate, audio packet loss rate,
conference participating duration, and presentation token. Call status is displayed only
when your TE30 is in use during a conference.

l

Conference parameters: includes the call bandwidth, video protocol, video bandwidth
(frame rate), audio protocol, audio bandwidth, presentation protocol, presentation
bandwidth (frame rate), remote number, H.235 encryption status, conference ID for video
access, conference ID for audio access, ISDN trunk number, conference ID for ISDN
access, and password for conference authentication. Conference parameters are displayed
only when your TE30 is in use during a conference.

l

Input port status: includes the video information about the built-in camera and VGA IN
port. For example,

DVI 1080p 60Hz

indicates that the input mode, video resolution, and

refresh rate of the built-in camera are DVI, 1080p, and 60 Hz. respectively.

13.1.4 Viewing System Information

System information helps you maintain your TE30.

Procedure

Choose

Advanced Settings

>

Diagnostics

>

System Information

.

The following information is displayed on the

System Information

screen:

l

Version information: includes the endpoint model, serial number, software version,
hardware information, logical version, and microphone array version.

l

Specification information: includes audio, video, ports, bandwidth, SIP, built-in MCU, dual
stream, security, and other main features of the TE30.

13.1.5 Querying Logs

Your TE30 logs all non-query events in real time, including user activities and commands. The
logs help with device maintenance, fault identification, and auditing.

HUAWEI TE30 Videoconferencing Endpoint
User Guide

13 Maintenance

Issue 01 (2013-03-27)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

116

«
...
122
123
124
125
126
...
»

Summary of Contents for TE30






























































































































































Reviews:

No comments

Related manuals for TE30

UNIVERGE SL2100

Brand: NEC Pages: 196

UNIVERGE SL2100

Brand: NEC Pages: 174

ElectraElite IPK

Brand: NEC Pages: 151

Ascotel Office 45

Brand: Aastra Pages: 40

Brand: Aastra Pages: 244

Brand: Aastra Pages: 30

Brand: Aastra Pages: 24

IntelliGate A150

Brand: Aastra Pages: 524

Ascotel IntelliGate 150

Brand: Aastra Pages: 228

Brand: Aastra Pages: 22

Brand: Daktronics Pages: 52

Brand: Hanwell Pages: 34

BALBOA CS6000B Series

Brand: HydroQuip Pages: 32

Box Design BT Box S2

Brand: Pro-Ject Audio Systems Pages: 6

Brand: J&M Pages: 8

Brand: Vansco Pages: 11

DE-3000+ Series

Brand: Altronic Pages: 77

Brand: Belson Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands