Huawei SUN2000-60KTL-M0 User Manual Download Page 92

Page: 92 / 127

No.

Parameter

Description

Unit

Grid reconnection

voltage lower limit

The standards of certain countries and regions

require that the SUN2000 must not export

power to the power grid again when the grid

voltage is below the value of Grid

reconnection voltage lower limit after the

SUN2000 shuts down due to a fault.

Grid reconnection

frequency upper limit

The standards of certain countries and regions

require that the SUN2000 must not export

power to the power grid again when the grid

frequency exceeds the value of Grid

reconnection frequency upper limit after the

SUN2000 shuts down due to a fault.

Grid reconnection

frequency lower limit

The standards of certain countries and regions

require that the SUN2000 must not export

power to the power grid again when the grid

frequency is below the value of Grid

reconnection frequency lower limit after the

SUN2000 shuts down due to a fault.

Reactive power

compensation (cosφ-

P) trigger voltage

Specifies the voltage threshold for triggering

reactive power compensation based on the

cosφ-P curve.

Reactive power

compensation (cosφ-

P) exit voltage

Specifies the voltage threshold for exiting

reactive power compensation based on the

cosφ-P curve.

7.2.2.2 Setting Protection Parameters

Procedure

Step 1 Choose Function Menu > Settings > Protection Parameters to access the

settings screen.

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

7 Man-Machine Interactions

Issue 06 (2020-10-12)

Summary of Contents for SUN2000-60KTL-M0
































































































































Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands

Huawei SUN2000-60KTL-M0, User Manual

Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands