Huawei SUN2000-60KTL-M0 User Manual Download Page 112

Page: 112 / 127

Handling the Inverter

9.1 Removing the SUN2000

NO TICE

Before removing the SUN2000, disconnect both AC and DC connections.

Perform the following operations to remove the SUN2000:
1. Disconnect all cables from the SUN2000, including RS485 communications

cables, DC input power cables, AC output power cables, and PGND cables.

2. Remove the SUN2000 from the mounting bracket.
3. Remove the mounting bracket.

9.2 Packing the SUN2000

●

If the original packing materials are available, put the SUN2000 inside them

and then seal them by using adhesive tape.

●

If the original packing materials are not available, put the SUN2000 inside a

suitable cardboard box and seal it properly.

9.3 Disposing of the SUN2000

If the SUN2000 service life expires, dispose of it according to the local disposal

rules for electrical equipment waste.

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

9 Handling the Inverter

Issue 06 (2020-10-12)

105

Summary of Contents for SUN2000-60KTL-M0
































































































































Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands

Huawei SUN2000-60KTL-M0, User Manual

Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands