manualshive.com logo in svg

Huawei SUN2000-43KTL-IN-C1, User Manual

Share
Download
Huawei SUN2000-43KTL-IN-C1 User Manual Download Page 86

SUN2000-43KTL-IN-C1 
User Manual 

8 Maintenance 

 

Issue 07 (2018-05-06) 

Copyright © Huawei Technologies Co., Ltd. 

80 

 

8 

Maintenance 

8.1 Routine Maintenance 

To ensure that the SUN2000 can operate properly for a long term, you are advised to perform 
routine maintenance on it as described in this chapter. 

 

 

 

Before cleaning the system, and maintaining the cable connections and grounding 
reliability, power off the system (see 

6.3 Powering Off the SUN2000

) and ensure that the 

two DC switches on the inverter are OFF. 

 

If you need to open the maintenance compartment door in rainy or snowy days, take 
protective measures to prevent rain and snow entering the maintenance compartment. If it 
is impossible to take protective measures, do not open the maintenance compartment door 
in rainy or snowy days. 

Table 8-1

 

Maintenance list 

Item 

Check Method 

Maintenance Interval 

System cleanliness 

Check periodically that the heat sinks 
are free from obstacles or dust. 

Once six months to a 
year 

System running 
status 

 

Check that the inverter is not 
damaged or deformed. 

 

Check that the running sound of the 
inverter is normal. 

 

When the inverter is running, check 
that all inverter parameters are 
correctly set. 

Once six months 

Summary of Contents for SUN2000-43KTL-IN-C1




































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands