Huawei SUN2000-43KTL-IN-C1 User Manual Download Page 13

Page: 13 / 99

SUN2000-43KTL-IN-C1
User Manual

2 Overview

Issue 07 (2018-05-06)

Table 2-2

LED indicator description (from left to right)

Indicator

Status

Meaning

PV connection
indicator

Green on

At least one PV string is
properly connected, and
the DC input voltage of
the corresponding MPPT
circuit is higher than or
equal to 200 V.

Green off

The SUN2000
disconnects from all PV
strings, or the DC input
voltage of each MPPT
circuit is less than 200 V.

Grid-tied indicator

Green on

The SUN2000 connects
to the power grid.

Green off

The SUN2000 does not
connect to the power grid.

Communications
indicator

Blinking green at short intervals (on for
0.5s and then off for 0.5s)

The SUN2000 receives
data over RS485/PLC
communication.

Green off

The SUN2000 has not
received data over
RS485/PLC
communication for 10
seconds.

Alarm/Maintenanc
e indicator

Alarm status

Blinking red at long
intervals (on for 1s
and then off for 4s)

A warning alarm is
generated.

Blinking red at short
intervals (on for 0.5s
and then off for 0.5s)

A minor alarm is
generated.

Steady red

A major alarm is
generated.

Local
maintenance
status

Blinking green at
long intervals (on for
1s and then off for
1s)

Local maintenance is in
progress.

Blinking green at
short intervals (on
for 0.125s and then
off for 0.125s)

Local maintenance fails.

Steady green

Local maintenance
succeeds.

Summary of Contents for SUN2000-43KTL-IN-C1




































































































Search results

Summary of Contents for SUN2000-43KTL-IN-C1

Reviews:

Brands by name

Popular brands

Huawei SUN2000-43KTL-IN-C1, User Manual

Search results

Summary of Contents for SUN2000-43KTL-IN-C1

Reviews:

Brands by name

Popular brands