Huawei SUN2000-2KTL-L1 User Manual Download

Page: 101 / 122

SUN2000 Disposal

9.1 Removing a SUN2000

Procedure

Step 1 Power off the SUN2000. For details, see

8.1 System Power-Off

Step 2 Disconnect all cables from the SUN2000, including signal cables, DC input power

cables, battery cables, AC output power cables, and PE cables.

Step 3 Remove the WLAN antenna or the Smart Dongle from the SUN2000.
Step 4 Remove the SUN2000 from the mounting bracket.
Step 5 Remove the mounting bracket.

----End

9.2 Packing a SUN2000

●

If the original packaging is available, put the SUN2000 inside it and then seal

it using adhesive tape.

●

If the original packaging is unavailable, put the SUN2000 inside a suitable

hard carton and seal it properly.

9.3 Disposing a SUN2000

If the SUN2000 service life expires, dispose the SUN2000 according to the local

disposal rules for electrical equipment and electronic component waste.

SUN2000-(2KTL-6KTL)-L1

User Manual

9 SUN2000 Disposal

Issue 04 (2021-04-01)

Summary of Contents for SUN2000-2KTL-L1



























































































































Search results

Summary of Contents for SUN2000-2KTL-L1

Reviews:

Related manuals for SUN2000-2KTL-L1

Brands by name

Popular brands

Huawei SUN2000-2KTL-L1, User Manual

Search results

Summary of Contents for SUN2000-2KTL-L1

Reviews:

Related manuals for SUN2000-2KTL-L1

Brands by name

Popular brands