Huawei SUN2000-175KTL-H0 User Manual Download Page 75

Page: 75 / 94

SUN2000-(175KTL-H0, 185KTL-INH0, 185KTL-H1)
User Manual

8 Maintenance

Issue 02 (2019-06-05)

Removing the baffle of the air intake vent

Figure 8-1

Removing the baffle

8.3 Replacing a Fan



Before replacing a fan, power off the inverter.



When replacing a fan, use insulation tools and wear personal protective devices.

If the fan tray gets stuck when being pulled or pushed, slightly lift it.

Step 1

Remove the screw on the fan tray and save it. Pull out the fan tray until the fan baffle plate
aligns with the inverter chassis.

Figure 8-2

Pulling out fan tray (1)

Step 2

Remove the cable ties shared by the cables, unscrew the connectors, and disconnect the
cables.

Summary of Contents for SUN2000-175KTL-H0































































































Search results

Summary of Contents for SUN2000-175KTL-H0

Reviews:

Related manuals for SUN2000-175KTL-H0

Brands by name

Popular brands

Huawei SUN2000-175KTL-H0, User Manual

Search results

Summary of Contents for SUN2000-175KTL-H0

Reviews:

Related manuals for SUN2000-175KTL-H0

Brands by name

Popular brands