Huawei SUN2000-175KTL-H0 User Manual Download Page 64

Page: 64 / 94

SUN2000-(175KTL-H0, 185KTL-INH0, 185KTL-H1)
User Manual

7 Man-Machine Interactions

Issue 02 (2019-06-05)

7.2.2.1 Setting Grid Parameters

Procedure

Step 1

Choose

Function Menu

Settings

Grid Parameters

to go to the parameter setting screen.

Figure 7-5

Power grid parameters (special user)

----End

Parameters

Vn represents the rated voltage and Fn represents the rated frequency.

No.

Parameter

Description

Grid code

Set this parameter based on the grid code of the
country or region where the SUN2000 is used and
the SUN2000 application scenario.

Auto start upon grid recovery

Specifies whether to allow the SUN2000 to
automatically start after the power grid recovers.

Grid connection duration after power
grid recovery

Specifies the waiting time for SUN2000 restart
after the power grid recovers.

Grid reconnection voltage upper limit

The standards of certain countries and regions
require that the SUN2000 must not export power to
the power grid again when the grid voltage exceeds
the value of

Grid reconnection voltage upper

limit

after the SUN2000 shuts down due to a fault.

Summary of Contents for SUN2000-175KTL-H0































































































Search results

Summary of Contents for SUN2000-175KTL-H0

Reviews:

Related manuals for SUN2000-175KTL-H0

Brands by name

Popular brands

Huawei SUN2000-175KTL-H0, User Manual

Search results

Summary of Contents for SUN2000-175KTL-H0

Reviews:

Related manuals for SUN2000-175KTL-H0

Brands by name

Popular brands