Huawei SUN2000-10KTL-M0 User Manual Download

Page: 62 / 112

Commissioning

6.1 Check Before Power-On

Table 6-1 Installation checklist

No.

Check Item

Acceptance Criteria

SUN2000 installation

The SUN2000 is installed correctly, securely, and

reliably.

Smart Dongle

The Smart Dongle is installed correctly and

securely.

Cable layout

Cables are routed properly as required by the

customer.

Cable tie

Cable ties are secured evenly and no burr exists.

Grounding

The ground cable is connected correctly,

securely, and reliably.

Turn off the switches

The DC SWITCH and all the switches connected

to the SUN2000 are set to OFF.

Cable connections

The AC output power cable and DC input power

cable are connected correctly, securely, and

reliably.

Unused terminals and ports

Unused terminals and ports are locked by

watertight caps.

Installation environment

The installation space is proper, and the

installation environment is clean and tidy,

without foreign matter.

SUN2000-(12KTL, 15KTL, 17KTL, 20KTL)-M0

User Manual

6 Commissioning

Issue 06 (2020-07-02)

Summary of Contents for SUN2000-10KTL-M0

















































































































Search results

Summary of Contents for SUN2000-10KTL-M0

Reviews:

Related manuals for SUN2000-10KTL-M0

Brands by name

Popular brands

Huawei SUN2000-10KTL-M0, User Manual

Search results

Summary of Contents for SUN2000-10KTL-M0

Reviews:

Related manuals for SUN2000-10KTL-M0

Brands by name

Popular brands