Huawei SmartAX MA5616 Configuration Manual Download

Page: 89 / 553

Figure 3-29

NTP peer mode

Precaution

In the peer mode, you need to configure the NTP mode only on the active peer.

The peers determine clock synchronization according to the clock stratum instead of
according to whether the peer is an active peer.

Procedure

Step 1

Configure the NTP active peer.
1.

Run the

ntp-service refclock-master

command to configure the local clock as the master

NTP clock, and specify the stratum of the master NTP clock.

Run the

ntp-service unicast-peer

command to configure the NTP peer mode, and specify

the IP address of the remote server that functions as the local timer server and the interface
for transmitting and receiving NTP packets.

NOTE

In this command,

ip-address

is a unicast address, which cannot be a broadcast address, a multicast

address, or the IP address of a reference clock.

After the source interface of the NTP packets is specified by

source-interface

, the source IP address

of the NTP packets is configured as the primary IP address of the specified interface.

Step 2

Add a VLAN L3 interface.

Run the

vlan

command to create a VLAN.

Run the

port vlan

command to add an upstream port to the VLAN so that the user packets

carrying the VLAN tag are transmitted upstream through the upstream port.

In the global config mode, run the

interface vlanif

command to create a VLAN interface,

and then enter the VLAN interface mode to configure the L3 interface.

Run the

ip address

command to configure the IP address and subnet mask of the VLAN

interface so that the IP packets in the VLAN can participate in the L3 forwarding.

----End

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands

Huawei SmartAX MA5616, Configuration Manual

Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands