Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 488 / 553

background image

Figure 9-17

Flowchart for configuring the triple play service in the multi-PVC for multiple

services mode

Procedure

l

Configure the Internet service.
1.

Create a VLAN and add an uplink port to the VLAN.

huawei(config)#

vlan 102 smart

huawei(config)#

port vlan 102 0/0 1

2.

Configure a traffic profile.

–

Because the VoIP, IPTV, and Internet services are provided through the same port,
you must set the 802.1p priority of each service.

–

Generally, the priorities are in a descending order for the VoIP service, IPTV
service, and Internet service. In this example, set the traffic profile index to 7 and
the 802.1p priority of the Internet service to 1.

huawei(config)#

traffic table ip index 7 cir 1024 priority 1 priority-

policy loca
l-Setting

3.

Add service ports to the VLAN.

Add service ports to the VLAN and use the traffic profile configured in the preceding
step.

huawei(config)#

service-port vlan 102 vdsl mode atm 0/1/0 vpi 0 vci 37 rx-

cttr 7 tx-cttr 7

huawei(config)#

service-port vlan 102 vdsl mode atm 0/1/1 vpi 0 vci 37 rx-

cttr 7 tx-cttr 7

4.

Save the data.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

477

«
...
486
487
488
489
490
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Sagem Pages: 19

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 44

Brand: Patton electronics Pages: 2

Brand: Patton electronics Pages: 86

Brand: Aleratec Pages: 12

Brand: MiLAN Pages: 1

PacketShaper PS-S200

Brand: Symantec Pages: 2

Brand: SUNRICH TECHNOLOGY Pages: 5

Brand: IEI Technology Pages: 86

Lite N42B1P Series

Brand: Dahua Technology Pages: 14

PISO-725 Series

Brand: ICP DAS USA Pages: 8

Brand: swiftech Pages: 2

CL-SOM-AM57 Series

Brand: CompuLab Pages: 79

Brand: Renesas Pages: 40

Brand: Abocom Pages: 1

Brand: Renesas Pages: 4

Xtreme Networked Boat

Brand: Broadband Products Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands