Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 445 / 553

background image

Configure the multicast uplink port, multicast programs, and multicast users.

igmp uplink-port 0/0/1
multicast-vlan 4002
igmp uplink-port 0/0/1
igmp match mode disable
igmp match group ip 224.1.1.1 to-ip 224.1.1.2
multicast-vlan 4003
igmp match mode disable
igmp match group ip 224.1.1.1 to-ip 224.1.1.2
btv
igmp user add service-port 100
igmp user add service-port 101
multicast-vlan 4002
igmp multicast-vlan member service-port 100
multicast-vlan 4003
igmp multicast-vlan member service-port 101
quit
save

9.3 Configuration Example of the VoIP Service

This topic describes how to configure the VoIP service based on the H.248 or SIP protocol.

9.3.1 Configuration Example of the VoIP PSTN Service (Based on
the H.248 Protocol)

This topic describes how to configure the VoIP service based on the H.248 protocol.

Service Requirements

In an office, the MA5616 that adopts the H.248 protocol is newly deployed. Data plan and
configuration, however, are not performed on the MGC (softswitch) connected to the
MA5616. The following voice services are required:

l

POTS service needs to be provided for phone 0-phone 31 for 32 users.

l

Polarity reversal charging is adopted.

Prerequisite

l

According to the actual network, a route from the MA5616 to the MGC must be configured
to ensure that the MA5616 and the MGC are reachable to each other.

l

POTS service board ASRB must be inserted into the planned slot, and the RUN ALM
indicator on the board must be green and must be on for 1s and off for 1s repeatedly.

Networking

shows the example network of the VoIP service based on the H.248 protocol.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

434

«
...
443
444
445
446
447
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

All in One Printer

Brand: Baracoda Pages: 42

Brand: H3C Pages: 33

S5500-SI Series

Brand: H3C Pages: 1217

Brand: 3Com Pages: 2443

Brand: H3C Pages: 3

Brand: H3C Pages: 4

Brand: Opengear Pages: 2

Brand: ZyXEL Communications Pages: 125

Brand: FONESTAR Pages: 8

Brand: ZALMAN Pages: 8

Brand: Maipu Pages: 26

Brand: Kontron Pages: 62

32 bit 10/100 Fast Ethernet Card A02-S32-S

Brand: Atlantis Land Pages: 9

Prestige 642R Series

Brand: ZyXEL Communications Pages: 163

Brand: LanReady Pages: 40

Brand: Lantech Pages: 23

Brand: Adaptec Pages: 3

EK-FC670 GTX Series

Brand: ekwb Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands