Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 224 / 553

background image

7.1.1.1 Configuring the Upstream VLAN Interface

This topic describes how to specify the upstream VLAN interface for the media stream and
signaling stream, and how to configure the IP addresses of the L3 interface. These IP addresses
are the sources of the media and signaling IP address pools.

Context

Multiple IP addresses can be configured for the same VLAN L3 interface. Only one IP address
functions as the primary address, and other IP addresses function as the secondary addresses.

Procedure

Step 1

Add an upstream VLAN.

Run the

vlan

command to add an upstream VLAN for the media stream and signaling stream.

Step 2

Add an upstream port to the VLAN.

Run the

port vlan

command to add an upstream port to the VLAN.

Step 3

Configure the IP addresses of the VLAN L3 interface.
1.

Run the

interface vlanif

command to enter the L3 interface of the upstream VLAN for the

media stream and signaling stream.

2.

Run the

ip address

command to configure the IP addresses of the L3 interface.

Step 4

Check whether the IP addresses of the L3 interface are the same as those in the data plan.

Run the

display interface vlanif

command to check whether the IP addresses of the L3 interface

are the same as those in the data plan.

----End

Example

Assume that the media stream and signaling stream are transmitted upstream through upstream
port 0/0/1. To create media and signaling upstream VLAN 3 and configure IP addresses
10.13.4.116/16 and 10.13.4.117/16 of the L3 interfaces for the media IP address pool and the
signaling IP address pool respectively, do as follows:

huawei(config)#

vlan 3 smart

huawei(config)#

port vlan 3 0/0 1

huawei(config)#

interface vlanif 3

huawei(config-if-vlanif3)#

ip address 10.13.4.116 16

huawei(config-if-vlanif3)#

ip address 10.13.4.117 16 sub

huawei(config-if-vlanif3)#

quit

huawei(config)#

display interface vlanif 3

vlanif3 current state : UP
Line protocol current state : UP
Description : HUAWEI, SmartAX Series, vlanif3 Interface
The Maximum Transmit Unit is 1500 bytes
Internet Address is 10.13.4.116/16
Internet Address is 10.13.4.117/16 Secondary
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 00e0-fc32-1118

7.1.1.2 Configuring the Media and Signaling IP Address Pools

The media IP address pool defines all media IP addresses that can be used by the AG, and the
signaling IP address pool defines all signaling IP addresses that can be used by the AG.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

213

«
...
222
223
224
225
226
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Patton electronics Pages: 2

Brand: Patton electronics Pages: 86

Brand: Palo Alto Network Pages: 56

Brand: AMD Pages: 20

Brand: Black Box Pages: 9

Scorpio WD2500BPVT

Brand: Western Digital Pages: 3

Scorpio WD2500BPVT

Brand: Western Digital Pages: 4

Brand: Aewin Technologies Pages: 86

Brand: Aaeon Pages: 72

Brand: Leviton Pages: 4

Slideaway CL1008

Brand: ATEN Pages: 77

Brand: FiberHome Pages: 2

Brand: Alcatel-Lucent Pages: 12

Brand: Planet Pages: 54

Brand: ENERMAX Pages: 33

Brand: Netequalizer Pages: 14

Brand: R.V.R. Elettronica Pages: 171

RJModem MT5656RJ

Brand: Multi-Tech Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands