Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 220 / 553

background image

Table 7-1

Data plan for configuring the VoIP PSTN service based on the H.248 protocol

Item

Remarks

MG interface
data
(The data
configuration
must be
consistent with
the data
configuration
on the MGC.)

Parameter
s of the
media
stream and
signaling
stream

Media and
signaling
upstream VLAN

It is used as the upstream VLAN of the
VoIP service to be configured. Standard
VLAN is recommended.

Media and
signaling
upstream port

It is used as the upstream port of the
VoIP service to be configured.

Media IP address
and signaling IP
address

These IP addresses must be selected
from the media and signaling IP address
pools. The media and signaling IP
address pools consist of all the IP
addresses of the L3 interface of the
media and signaling upstream VLAN.

Default IP address
of the MG

It is the IP address of the next hop from
the MA5616 to the MGC.

Attribute
parameter
s of the
MG
interface

NOTE

Parameter
s listed
here are
mandator
y, which
means
that the
MG
interface
fails to be
started if
these
parameter
s are not
configure
d.

MG interface ID

It is the MG interface ID used for the
VoIP service to be configured. The
MA5616 supports only one virtual
access gateway (VAG).

Signaling port ID
of the MG
interface

It is the transport layer protocol port ID
used for the signaling exchange
between the MA5616 (AG) and the
MGC.
Default signaling port ID specified in
the H.248 protocol: 2944 (text) and
2945 (binary)

IP address of the
primary MGC to
which the MG
interface belongs

When dual homing is not configured,
the parameters of the primary MGC
need to be configured. When dual
homing is configured, the IP address
and the port ID of the secondary MGC
also need to be configured.

Port ID of the
primary MGC to
which the MG
interface belongs

Coding mode of
the MG interface

Currently, only the

text

coding mode is

supported.

Transmission
mode of the MG
interface

The transmission mode is selected
according to the requirements on the
MGC side. Generally, UDP is adopted.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

209

«
...
218
219
220
221
222
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

IES615-2D Series

Brand: 3onedata Pages: 3

Brand: 3One data Pages: 5

Brand: 3onedata Pages: 33

Brand: Zonet Pages: 8

Brand: Direct IP Pages: 76

Brand: LogLogic Pages: 30

Brand: Mercusys Pages: 35

Active Module Carrier VX402C-64

Brand: C&H Pages: 32

Brand: TP-Link Pages: 2

Brand: IBM Pages: 72

Open Standard Module RPX30 EVA-MI V1

Brand: iesy Pages: 9

Routers and Switches

Brand: Allied Telesis Pages: 15

Brand: Patton electronics Pages: 40

Brand: TP-Link Pages: 2

Brand: Telit Wireless Solutions Pages: 79

Brand: IBM Pages: 8

Brand: TP-Link Pages: 17

RouterBOARD RB711-5HnD

Brand: MikroTik Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands