Huawei RU3632 Installation Manual Download Page 104

Page: 104 / 128

RRU3832&RRU3632
Installation Guide

9 Installing RU Cables

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Cable

One End

The Other End

Connector

Installation
Position

Connector

Installation
Position

connector

CPRI Fiber
Optic
Cable(RU38
32)

DLC connector

CPRI0 port on
the RU

DLC connector

CPRI port on a
board in the BBU
or CPRI1 port on
the upper-level
RU

CPRI1 port on
the RU

CPRI0 port on
the lower-level
RU

CPRI Fiber
Optic
Cable(RU36
32)

DLC connector

CPRI0 port on
the RU

DLC connector

CPRI port on a
board in the BBU

RU RF
Jumper

DIN male
connector

ANT_TX/RX
A,
ANT_TX/RX
B, ANT_RXC,
or ANT_RXD
port on the RU

DIN male
connector

Antenna system

RU AISG
Multi-Wire
Cable

DB9 waterproof
male connector

RET port on
the RU

Standard AISG
female connector

Standard AISG
male connector
on the RCU or on
the AISG
extension cable

RU AISG
Extension
Cable

Standard AISG
male connector

Standard AISG
female
connector on
the AISG
multi-wire
cable

Standard AISG
female connector

Standard AISG
male connector
on the RCU

9.5 Installing an RU PGND Cable

This section describes the procedure for installing an RU PGND cable.

Context

The cross-sectional area of an RU PGND cable is 16 mm

(0.025 in.

). The cable has an M6

OT terminal at one end and an M8 terminal at the other end.

Summary of Contents for RU3632

































































































































Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands

Huawei RU3632, Installation Manual

Search results

Summary of Contents for RU3632

Reviews:

Related manuals for RU3632

Brands by name

Popular brands