manualshive.com logo in svg

Huawei RRU3268, Installation Manual

Share
Download
Huawei RRU3268 Installation Manual Download Page 78

Figure 8-29

 Installing the RRU mounting brackets

 

NOTE

Verify that the arrows on the mounting brackets are pointing up.

1.

Adjust the position of the nut and remove one end of the square-neck bolt from the slot on
the auxiliary bracket.

2.

Slide the mounting brackets onto the angle steel horizontally and insert the square-neck
bolt into the slot.

Step 3

Use a 16 mm (0.67 in.) M10 torque wrench to tighten the nuts to 40 N·m (354.03 lbf·in.) so that
the mounting brackets are secured onto the angle steel, as shown in 

Figure 8-30

.

CAUTION

Tighten the nuts on the two square-neck bolts alternatively. After the main and auxiliary brackets
are secured properly, measure the spacing between the brackets on both sides and ensure that
the spacing is the same on the two sides.

RRU3268
Installation Guide

8 Installing the RRU

Issue ()

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

70

Summary of Contents for RRU3268




































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands