Huawei RRU3262 Installation Manual Download Page 106

Page: 106 / 130

Cable

One End

The Other End

Connector

Installation
Position

Connector

Installation
Position

RRU Power
Cable

Tool-less female
connector
(pressfit type)

NEG(-) and
RTN(+) ports
on the RRU

Depending on the
power equipment

External power
equipment

RRU Alarm
Cable

Waterproof
DB15 male
connector

EXT_ALM
port on the
RRU

Cord end
terminal

External alarm
device

CPRI Fiber
Optic Cable
(in
multimode
scenarios)

DLC connector

CPRI0 port on
the RRU
CPRI1 port on
the RRU

DLC connector

A CPRI port on a
board in the BBU

CPRI Fiber
Optic Cable
(in single-
mode
scenarios)

DLC connector

CPRI0 port on
the RRU

DLC connector

A CPRI port on a
board in the BBU

RRU RF
Jumper

DIN male
connector

RF ports on the
RRU

DIN male
connector

Antenna system

RRU AISG
Multi-Wire
Cable

Waterproof DB9
male connector

RET port on
the RRU

Standard AISG
female connector

Standard AISG
male connector
on the RCU or on
the AISG
extension cable

RRU AISG
Extension
Cable

Standard AISG
male connector

Standard AISG
female
connector on
the AISG
multi-wire
cable

Standard AISG
female connector

Standard AISG
male connector
on the RCU

9.5 Installing an RRU PGND Cable

This section describes the procedure for installing an RRU PGND cable.

Context

The cross-sectional area of an RRU PGND cable is 16 mm

(0.025 in.

). The cable has an M6

OT terminal at one end and an M8 terminal at the other end.

RRU3262
Installation Guide

9 Installing RRU Cables

Issue 01 (2014-11-20)

Huawei Proprietary and Confidential

Summary of Contents for RRU3262



































































































































Search results

Summary of Contents for RRU3262

Reviews:

Huawei RRU3262, Installation Manual, Page: 106 / 130

Search results

Summary of Contents for RRU3262

Reviews: