Huawei pRRU3901 Maintenance Manual Download Page 20 | Manualshive

Page: 20 / 52

background image

4.2 Powering Off the RHUB

An RHUB can be powered off in two ways: normal power-off and emergency power-off. You
need to perform a normal power-off in scenarios such as an equipment swap or foreseeable
regional blackout, and you need to perform an emergency power-off in emergencies such as a
fire, smoke, or water damage in indoor scenarios.

Procedure

l

Normal power-off

NOTICE

Powering off the RHUB interrupts services, and therefore perform associated operations
before a power-off.

1.

Remove the power plug to disconnect the RHUB with the external power input.

2.

If the RHUB is equipped with an external power device, turn off the switch of the
external power device.

l

Emergency power-off
1.

Turn off the switch of the external power device.

----End

LampSite
Site Maintenance Guide

4 Powering On and Powering Off the RHUB

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

12

«
...
18
19
20
21
22
...
»

Summary of Contents for pRRU3901





















































Reviews:

No comments

Related manuals for pRRU3901

Brand: Federal Signal Corporation Pages: 13

Brand: Hammond Pages: 754

Brand: cam Pages: 2

Brand: Waycon Pages: 8

AVCCAM AG-HMR10

Brand: Panasonic Pages: 4

Brand: Banner Pages: 12

One Step BRZ0070

Brand: Baby Brezza Pages: 4

Brand: Babboe Pages: 7

Brand: Babboe Pages: 7

Brand: Jeda Pages: 8

Brand: madebyzen Pages: 16

Brand: R-Go Pages: 2

Brand: R&S Pages: 52

Brand: Vello Pages: 8

Brand: Panasonic Pages: 72

AS5000 - Transcription Kit - Digital Voice...

Brand: Olympus Pages: 17

Brand: Jackco Pages: 11

V2 SUPERCHARGER

Brand: Tesla Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands