Huawei OceanStor 18500 V3 Features Manual Download Page 33 | Manualshive

Page: 33 / 183

background image

Figure 1-12

Parallel 3DC configuration in asynch asynchronous mode

Storage System

LUN

Production

center

Site A

Storage System

Intra-city DR

center

Site B

Storage System

Site C

LUN

Remote DR

center

Asynchronous

Remote

Replication

Optical fiber cable

Network cable

LUN

Asynchronous

Remote

Replication

The parallel 3DC configuration in asynch asynchronous mode meets the following
service requirements:

l

Real-time backup and remote backup of data ensure the reliability of critical service data
and ensure that critical service data has two copies.

l

Data backup of the remote DR center (C) does not depend on the intra-city DR center
(B). If the intra-city DR center (B) or remote DR center (C) fails, the production center
(A) still has a backup site.

l

When a disaster occurs at the production center (A), the intra-city DR center (B) takes
over services immediately and recovers data. If the disaster also affects the intra-city DR
center (B), data in the remote DR center (C) is still available.

NOTE

The difference between 3DC in synch asynchronous and asynch asynchronous modes
lies in the different data synchronization modes of the production center (A) and intra-city DR center
(B). For the data synchronization mode used by the 3DC in synch asynchronous mode, when
data is concurrently written to the production center (A) and intra-city DR center (B), a message is
displayed indicating that the synchronization succeeds. For the data synchronization mode used by the
3DC in asynch asynchronous mode, when data is concurrently written to the production center
(A), a message is displayed indicating that the synchronization succeeds.

OceanStor V3 Series
Remote Replication Feature Guide for Block

1 Feature Description

Issue 06 (2018-01-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

25

«
...
31
32
33
34
35
...
»

Summary of Contents for OceanStor 18500 V3
























































































































































































Reviews:

No comments

Related manuals for OceanStor 18500 V3

Brand: LaCie Pages: 22

Brand: Omlet Pages: 4

Brand: Seagate Pages: 28

Brand: Supero Pages: 112

Brand: PEAKnx Pages: 14

StoraXe PowerBooster GSS0608

Brand: ADS-tec Pages: 140

Brand: Yardmaster Pages: 20

Brand: Seville Classics Pages: 7

Brand: U-Line Pages: 3

Brand: LaCie Pages: 27

Brand: Homak Pages: 3

Brand: DIVERSIFIED WOODCRAFTS Pages: 6

Brand: Infrant Technologies Pages: 98

Brand: AA Products Pages: 8

Brand: NEC Pages: 69

Brand: Facom Pages: 2

Brand: Shugart Pages: 49

Brand: Costway Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands