Huawei NetCol5000-C030 Series User Manual Download Page 76 | Manualshive

Page: 76 / 215

Huawei NetCol5000-C030 Series User Manual Download Page 76

Prerequisites

NO TICE

Before connecting power cables, use a multimeter to check that there is no

voltage between conducting wires and between conducting wires and the ground.

Procedure

Step 1 Take out OT terminals and cord end terminals from the fittings bag, and prepare

cables.

NO TICE

● Crimp the cables firmly and ensure that they are not loose after pulling.
● If the cables are not recommended specifications, you need to prepare the

terminals by yourself.

Step 2 Remove the cover of the electric control box.

1. Remove the four screws from the cover of the electric control box using an

M5 screwdriver.

2. Push the cover upward and take out the cover from the positioning pins.
3. Pull the entire cover out of the cabinet.

Figure 3-49 Removing the cover of the electric control box (NetCol5000-C065)

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual

3 Installation

Issue 04 (2021-03-15)

Copyright © Huawei Technologies Co., Ltd.

68

«
...
74
75
76
77
78
...
»

Summary of Contents for NetCol5000-C030 Series
























































































































































































































Reviews:

No comments