Huawei MC509 Hardware Manual Download Page 64

Page: 64 / 78

HUAWEI MC509 Series CDMA LGA Module
Hardware Guide

Mechanical Specifications

Issue 02 (2013-05-06)

Huawei Proprietary and Confidential

Figure 6-3

Label for MC509

Figure 6-4

Label for MC509-a



The picture mentioned above is only for reference.



Make the film according to the drawing.



The silk-screen should be clear, without burrs, and dimension should be accurate.



This nameplate should not be covered by the film.



The material and surface finishing and coatings which used have to make satisfied with the
RoHS directives.



The label must be heated up for 20s

–40s and able to endure the high temperature of

260ºC. And the color of the material of the nameplate can

’t change.

6.8 Customer PCB Design

6.8.1

PCB Surface Finish

The PCB surface finish recommended is Electroless Nickel, immersion Gold (ENIG).
Organic Solderability Preservative (OSP) may also be used, ENIG preferred.

28mm

R=1mm

1.1*1.1mm

MC509

QISMC509

5mm

28mm

R=1mm

1.1*1.1mm

A : 6.5mm

B : 5.1mm

B1: 4.7mm

A1 : 6.1mm

Summary of Contents for MC509















































































Search results

Summary of Contents for MC509

Reviews:

Related manuals for MC509

Brands by name

Popular brands

Huawei MC509, Hardware Manual

Search results

Summary of Contents for MC509

Reviews:

Related manuals for MC509

Brands by name

Popular brands