Huawei LUNA2000-30-S0 User Manual Download Page 66

Page: 66 / 129

Figure 4-7 Wall-mounted installation dimensions

Procedure

Step 1 Determine the positions for drilling holes using the marking-off template. Level

the positions of mounting holes using a level, and mark the positions with a

marker.

Step 2 Install the mounting kit.

D ANGER

When drilling holes, avoid the water pipes and power cables buried in the wall.

NO TE

M12x60 expansion bolts delivered with the battery are used to fix the wall mounting

support. If the length and quantity of the bolts do not meet installation requirements,

prepare M12 stainless steel expansion bolts by yourself.
M6x60 expansion bolts delivered with the battery are used to fix the power control module.

If the length and quantity of the bolts do not meet installation requirements, prepare M6

stainless steel expansion bolts by yourself.

LUNA2000-(5-30)-S0

User Manual

4 System Installation

Issue 07 (2022-01-10)

Summary of Contents for LUNA2000-30-S0


































































































































Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands

Huawei LUNA2000-30-S0, User Manual

Search results

Summary of Contents for LUNA2000-30-S0

Reviews:

Related manuals for LUNA2000-30-S0

Brands by name

Popular brands