Huawei IPC6125-WDL-FA Configuration Manual Download Page 174 | Manualshive

Page: 174 / 202

background image

Parameter

Description

Rate limit

Sets the maximum upload rate for video buffering or
download rate for SD card recording.
It is recommended that the value be one fourth of the
bit rate of primary streams and not exceed the
available bandwidth.

NOTE

l

The video buffering function occupies additional
network bandwidth. If the value exceeds the available
bandwidth, the network may be blocked, which leads
to image exceptions. Set

Rate limit

based on the site

requirements.

l

The rate for downloading the recordings in the SD card
can be adjusted. However, the rate cannot be adjusted
during the download.

SD card
recording time

Sets the SD card recording duration. The SD card
recording automatically stops when the specified
recording duration ends.
The recording duration ranges from 5 minutes to
1440 minutes.

NOTE

In

Record status

, you can view the status of recordings of different types.

l

Running

: The recording is enabled.

l

Stop

: The recording is disabled.

----End

14.5 Setting Local Parameters

You can set local parameters, such as the protocol type, data stream type, video stream type,
and path where snapshots are saved. These settings take effect only on the local PC.

Procedure

Step 1

Choose

Settings

>

System Configuration

>

Local Parameters

.

The

Local Parameters

page is displayed, as shown in

Figure 14-14

.

IPC6125-WDL-FA
Configuration Guide

14 Managing the System

Issue 01 (2016-08-20)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

168

«
...
172
173
174
175
176
...
»

Summary of Contents for IPC6125-WDL-FA











































































































































































































Reviews:

No comments

Related manuals for IPC6125-WDL-FA

axis CC20 Series

Brand: Audioxtra Pages: 3

Brand: Zenza Bronica Pages: 29

Brand: Yada Pages: 20

Brand: Safety Vision Pages: 21

Disccovery 290S ZOOM Date

Brand: FujiFilm Pages: 32

Brand: Ikegami Pages: 35

Brand: Papago Pages: 100

Brand: FashionCam Pages: 6

Brand: Foscam Pages: 2

Brand: Lamax Electronics Pages: 80

Brand: Bresser Pages: 28

Brand: FujiFilm Pages: 2

Prosilica GT LF Series

Brand: Allied Vision Pages: 229

Brand: Casio Pages: 37

Brand: switel Pages: 48

Brand: Basler Pages: 170

Brand: Kodak Pages: 2

Brand: Trevi Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands