Huawei IPC6122-P Configuration Manual Download Page 95

Page: 95 / 115

NOTE

The unicast mode is efficient and targeted, but may result in high loads on the IPC.

The multicast mode reduces the IPC loads but does not provide error correction functionality.

----End

12.8 Upgrading the IPC

You can upgrade an IPC.

NOTICE

The upgrade time is less than 5 minutes (excluding the restart time) if a maximum of one
channel of video streams is enabled.

It is recommended that you perform the upgrade when few or no users are online.

During the upgrade, ensure that the IPC is powered on, network cables are properly
connected, and no other operation is performed.

When the version is upgraded, it is recommended that you clear the browser cache data
before next login.

Prerequisites

You have obtained the upgrade package.

Obtaining Upgrade Packages: Visit and log in

http://support.huawei.com/enterprise

choose

Product Category

Unified Communications and Collaboration

Video

Surveillance

IP Cameras

, go to the required product directory, select a required IPC

version, and select the upgrade package to download under

Version and Patch

Procedure

Step 1

Choose

Settings

System Configuration

Device Maintenance

The

Device Maintenance

page is displayed, as shown in

Figure 12-13

IPC6122-P
Configuration Guide

12 Managing the System

Issue 02 (2016-04-06)

Huawei Proprietary and Confidential

Summary of Contents for IPC6122-P




















































































































Search results

Summary of Contents for IPC6122-P

Reviews:

Related manuals for IPC6122-P

Brands by name

Popular brands

Huawei IPC6122-P, Configuration Manual

Search results

Summary of Contents for IPC6122-P

Reviews:

Related manuals for IPC6122-P

Brands by name

Popular brands