Huawei IDS1000 User Manual Download Page 61

Page: 61 / 67

IDS1000 Container Data Center
User Manual

7 Parts Replacement

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

7.10 Replacing a Gas Extinguishing Controller

Prerequisites



A gas extinguishing controller is faulty.



Spare gas extinguishing controllers are available.

Tools and Materials



Diagonal pliers



PVC insulation tape



Spare gas extinguishing controllers



Documents delivered with the gas extinguishing controller



Gloves



Key to the gas extinguishing controller

Impact on the System

None

Procedure

Step 1

Open the door of gas extinguishing controller using a key.

Step 2

Power off the gas extinguishing controller.

Step 3

Open the gas extinguishing controller and make a note of the cable connection.

Step 4

Remove the cables and gas extinguishing controller.

Step 5

Install the new gas extinguishing controller and connect the cables.

Step 6

Switch on the circuit breaker for the fire extinguishing controller.

Step 7

Verify that the fire extinguishing controller is working properly and lock the door.

----End

Follow-up Procedure

Send the faulty fire extinguishing controller together with a

Repair Notice

to your local

Huawei office for repair.

Summary of Contents for IDS1000




































































Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands

Huawei IDS1000, User Manual

Search results

Summary of Contents for IDS1000

Reviews:

Related manuals for IDS1000

Brands by name

Popular brands