manualshive.com logo in svg

Huawei IAD108A, User Manual

The Huawei IAD108A is a versatile communication device that provides seamless connectivity. Unlock its full potential by accessing the user manual, available for free download at manualshive.com. This comprehensive manual offers valuable insights and step-by-step instructions to help you maximize the features and functionalities of your Huawei IAD108A.

Share
Download
background image

User Manual 
U-SYS IAD108 Integrated Access Device 

Chapter 7  Maintaining System 

 

7-59 

 

 

 

 

  Note: 

z

 

The difference between Running status and Active status is that the patches in 
Running status can automatically recover to Running status after the system is 
rebooted, while those in Active status will become Deactive after rebooting. 

z

 

The Active status can be regarded as the “trial running” of the patch. Through 
the trial running you can check whether the expected functions are achieved. 
Only the patches passed the trial running test can be used normally. 

 

The commands provided by the system for patching are listed in 

Table 7-18. 

Table 7-18

 

Commands used for patching 

Command  

Description 

patch active

 

It is used to activate the patch.

 

patch deactive

 

It is used to deactivate the patch. 

patch start

 

It is used to run the patch.

 

patch remove

 

It is used to delete the patch. 

show patch 

It is used to display the information of the patch. 

 

7.7.2  Steps of Operating Patches 

Patches can be operated in the following sequence: 

Summary of Contents for IAD108A








































































































































































































































































































Reviews:

No comments

Related manuals for IAD108A

Gallagher silencer Installation Manuals preview
silencer
Brand: Gallagher Pages: 2
Patton SmartNode 10100 Series Quick Start Manual preview
SmartNode 10100 Series
Brand: Patton Pages: 12
Patton FiberPlex FPX6000 Series Quick Start Manual preview
FiberPlex FPX6000 Series
Brand: Patton Pages: 20
Patton SmartNode 4970 Series User Manual preview
SmartNode 4970 Series
Brand: Patton Pages: 57
QUPIT 159-01 Installation Manual preview
159-01
Brand: QUPIT Pages: 16
BEC Ultimum 8900AX Quick Start Manual preview
Ultimum 8900AX
Brand: BEC Pages: 14
TANDBERG D13841.08 Administrator'S Manual preview
D13841.08
Brand: TANDBERG Pages: 54
Anywire ASLINK B2G78-PB1 User Manual preview
ASLINK B2G78-PB1
Brand: Anywire Pages: 50
Mako 7550-E Product Handbook preview
7550-E
Brand: Mako Pages: 70
Pepperl+Fuchs VBG-PN-K20-DMD-EV Installation Instructions Manual preview
VBG-PN-K20-DMD-EV
Brand: Pepperl+Fuchs Pages: 11
Innovaphone IP 400 Administrator'S Manual preview
IP 400
Brand: Innovaphone Pages: 164
Humanscale OfficeIQ Quick Start Manual preview
OfficeIQ
Brand: Humanscale Pages: 2
ZyXEL Communications P-793H 601156 Brochure preview
P-793H 601156
Brand: ZyXEL Communications Pages: 2
ZyXEL Communications P-661HNU Series Brochure preview
P-661HNU Series
Brand: ZyXEL Communications Pages: 2
ZyXEL Communications UAG Series Reference Manual preview
UAG Series
Brand: ZyXEL Communications Pages: 361
ZyXEL Communications P-663H-51 User Manual preview
P-663H-51
Brand: ZyXEL Communications Pages: 206
ZyXEL Communications P-660H Series User Manual preview
P-660H Series
Brand: ZyXEL Communications Pages: 466
tilgin HG2500 Series Quick Manual preview
HG2500 Series
Brand: tilgin Pages: 20

Brands by name

Popular brands

Load more brands