manualshive.com logo in svg

Huawei G5500, User Manual

Share
Download
Huawei G5500 User Manual Download Page 84

After login, the host name of the device is displayed on the left of the prompt.

----End

5.3.1.3 Logging In to the Management Module CLI Through the Management IP
Address of the Server Node

Scenarios

Log in to the management module CLI through the iBMC management IP address on the
server node.

Prerequisites

Conditions

The G5500 has been powered on.

Data

l

IP address of the iBMC management network port on the server node

l

User name and password for logging in to the iBMC of the server node

Software

PuTTY.exe

 (third-party software)

Procedure

Set the client address.

1

Set the IP address, subnet mask, or route of the client to enable the client to interconnect
with the iBMC management network port on the server node.
On the client, choose 

Start > Run

, enter 

cmd

, and click 

OK

. Then, run the 

Ping

 

IP

address of the aggregated management network port

 command to check whether the

management network port is reachable.

Log in to the iBMC WebUI of the server node.

For details, see 

5.4.1 Logging In to the iBMC WebUI

.

Enable the transparent transmission function.

2

In the navigation tree on the iBMC WebUI of the server node, choose 

Configure

 >

Service Settings

.

The 

Service Settings

 page is displayed.

NOTE

If the iBMC version is earlier than 

2.01

, the 

Port Settings

 page is displayed.

3

Enable 

HMM SSH NAT

 and set 

Port

 to 

30022

, as shown in 

Figure 5-6

.

FusionServer G5500 Server
User Guide

5 Configuring the G5500

Issue 02 (2017-12-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

76

Summary of Contents for G5500
























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands