Huawei G5500 User Manual Download Page 30

Page: 30 / 215

Figure 2-19

GP316 PCIe board components

Signal connector of riser 4

Power connector of riser 4

Expansion slot

Power connector of riser 3

Signal connector of riser 3

PCIe switch 2

Backplane guide sleeve

Backplane power connector

Backplane signal connector

PCIe switch 1

Signal connector of riser 1

Power connector of riser 1

Power connector of riser 2

Signal connector of riser 2

2.7.1 PCIe Slots

The following tables describe the mapping between the PCIe slots and the CPUs and
mezzanine cards, and list the PCIe standards.

Table 2-3

G560 PCIe slot description

PCIe
Device

CPU

PCIe
Standard

Connecto
r
Bandwid
th

Bus
Width

Port
Number

Slot Size

Mezzanin
e card 1

CPU 1

PCIe 3.0

Two x16

Port 3A
(through
PCIe
switch)

Non-
standard
device

FusionServer G5500 Server
User Guide

2 Components

Issue 02 (2017-12-15)

Huawei Proprietary and Confidential

Summary of Contents for G5500
























































































































































































































Search results

Summary of Contents for G5500

Reviews:

Brands by name

Popular brands

Huawei G5500, User Manual

Search results

Summary of Contents for G5500

Reviews:

Brands by name

Popular brands