Huawei FusionServer Pro 2288H V5 User Manual Download Page 82

Page: 82 / 177

Figure 7-1

Direction of heat dissipation

7.1.2 Temperature and Humidity Requirements

To ensure continued safe and reliable equipment operation, install or position the system in a
well-ventilated, climate-controlled environment.

Use temperature control devices all year long in any climates.

In dry and humid areas, maintain ambient humidity within range with humidifiers and
dehumidifiers respectively.

Table 7-1

Temperature and humidity requirements in the equipment room

Item

Description

Temperature

5ºC to 35ºC (41ºF to 95ºF)

Humidity

8% RH to 90% RH (non-condensing)

7.1.3 Cabinet Requirements

A general 19-inch cabinet with a depth of more than 1000 mm (39.37 in.) which
complies with the International Electrotechnical Commission 297 (IEC 297) standard.

Air filters installed on cabinet doors.

FusionServer Pro 2288H V5 Server
User Guide

7 Installation and Configuration

Issue 08 (2019-10-30)

Summary of Contents for FusionServer Pro 2288H V5


















































































































































































Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands

Huawei FusionServer Pro 2288H V5, User Manual

Search results

Summary of Contents for FusionServer Pro 2288H V5

Reviews:

Related manuals for FusionServer Pro 2288H V5

Brands by name

Popular brands