Huawei FusionModule500 User Manual Download Page 89

Page: 89 / 302

NO TICE

There should be a great sound of airflow during the exhausting.

Figure 4-17 Exhausting nitrogen from an indoor unit

(1) Pressure gauge

(2) Gas pipe needle valve

(3) Liquid pipe needle valve

NO TE

When exhausting nitrogen, do not remove the valve plug in case of losing it.

Step 3 After the airflow sound disappears, reinstall the needle valve nut.

----End

4.2.4.5 Installing an Outdoor Unit

4.2.4.5.1 Installation Requirements

Precautions

●

An outdoor unit must be installed by professionals.

●

When a smart cooling product needs to be moved or reinstalled, ask

professionals for help. Do not perform operations by yourself.

●

Do not store an outdoor unit in a damp environment such as a moist

basement or rain, because the humidity will cause short circuits.

Environmental Requirements

●

To avoid a fire disaster, install an outdoor unit in a dry and well-ventilated

place without flammable gas leakage.

●

Select a place away from direct sunlight and radiation from other heat

sources. If the sunlight or heat radiation cannot be avoided, cover the outdoor

unit.

●

Do not install an outdoor unit in a place with much salt or corrosive gas.

●

When installing the outdoor unit, ensure that the air intake vent and air

exhaust vent of the condenser are not dirty or blocked. Install an outdoor unit

in a clean area that is away from residential areas.

FusionModule500 Smart Mini Data Center

User Manual

4 Installation Guide

Issue 02 (2020-12-25)

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands