Huawei FusionModule500 User Manual Download Page 293

Page: 293 / 302

Figure 6-23 Connecting data and power cables to hard disks

4. Close the chassis cover, and use a PH2 screwdriver to fasten the rear screws.

Figure 6-24 Closing the chassis cover

Step 4 Observe the hard disk indicator to check whether the hard disk works properly.

----End

Follow-up Procedure

If the hard disk works abnormally, contact Huawei technical support.

6.4.3.9 Replacing a T/H Sensor (33010516)

Prerequisites

●

A T/H sensor needs to be replaced.

●

A spare T/H sensor of the same model is available and functional.

Procedure

Step 1 Tap Shutdown on the controller home screen.

NO TICE

Exercise caution because the device is still energized after it is shut down on the

controller home screen.

FusionModule500 Smart Mini Data Center

User Manual

6 O&M

Issue 02 (2020-12-25)

283

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands