Huawei FusionModule1000B V100R003C00 Page 99 Commissioning Manual Download

Page: 99 / 111

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

9 Commissioning Core Components

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

Figure 9-12

Temperature and humidity setting screen

Step 4

Verify the temperature and humidity settings by referring to the 30 kW chilled water precision
air conditioner temperature and humidity initial configuration table.

If any initial configuration is inconsistent with the initial setting, change it to the initial
setting.

----End

9.2.3 (Optional) Commissioning Civil Air Conditioners

Prerequisites

The power-on commissioning for the upstream PDB of air conditioners is completed.

Preparations

Tools: none

Documents: documents delivered with the civil air conditioners, power supply and
distribution system diagram, cooling device layout diagram

Skill requirement: cooling engineer

For the diagrams, see the initial configuration parameter manual for the solution in use.

Procedure

Step 1

Switch on the input power circuit breakers for air conditioners in the upstream PDB to power
on the air conditioners.

Summary of Contents for FusionModule1000B V100R003C00
















































































































Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands

Huawei FusionModule1000B V100R003C00, Commissioning Manual

Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands