Huawei FusionModule1000B V100R003C00 Page 53 Commissioning Manual Download

Page: 53 / 111

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

7 System Commissioning

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

Documents:

NetEco Commissioning Guide

NetEco Administrator Guide

, monitoring

component layout, initial configuration table of the management system

Skill requirement: weak-current engineer familiar with the management system



For the diagrams and tables, see the initial configuration parameter manual for the solution in use.



The

NetEco Administrator Guide

and

NetEco Commissioning Guide

are integrated in the

iManager

NetEco Product Documentation

Procedure

Step 1

Start the management system on the operation terminal. For details, see the

NetEco

Commissioning Guide

Step 2

Enter the initial user name and password on the NetEco WebUI to log in to the management
system.

Step 3

Check the connections of all monitoring devices by referring to the monitoring device layout
diagram.

Verify that all devices in the initial configuration table communicate with the management
system properly.

Step 4

Check that the views and videos in the management system are consistent with the running
status of the data center. For details, see

NetEco Commissioning Guide

and

NetEco

Administrator Guide

. If any inconsistency is found, contact Huawei technical support.

----End

7.4 Commissioning the Fire Extinguishing System
(Standard)

Prerequisites



The fire alarm control panel has been powered on.



The management system is working properly.

Summary of Contents for FusionModule1000B V100R003C00
















































































































Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands

Huawei FusionModule1000B V100R003C00, Commissioning Manual

Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands