Huawei FusionModule1000B V100R003C00 Page 108 Commissioning Manual Download

Page: 108 / 111

FusionModule1000B Water-Cooled IT Solution
Commissioning Guide

9 Commissioning Core Components

Issue 02 (2017-01-10)

Huawei Proprietary and Confidential

102

Figure 9-17

Removing the red pin

Step 4

Reinstall the protective cover of the emergency light.

Step 5

Insert the power plug of the emergency light.

The emergency light turns off, and the power indicator turns on.

Step 6

Press the red button of the emergency light. The emergency light turns on. When you release
the red button, the emergency light turns off.

Figure 9-18

Red button of the emergency light

(1) Red button of the emergency light



The red button is located at one side of the emergency light.



If the result expected for each step appears, the emergency light is working properly.

----End

9.6 Commissioning the VESDA

Preparations

Tools: smoke pistol

Summary of Contents for FusionModule1000B V100R003C00
















































































































Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands

Huawei FusionModule1000B V100R003C00, Commissioning Manual

Search results

Summary of Contents for FusionModule1000B V100R003C00

Reviews:

Related manuals for FusionModule1000B V100R003C00

Brands by name

Popular brands