Huawei FusionModule1000A Installation Manual Download Page 83

Page: 83 / 108

FusionModule1000A40 Prefabricated All-in-One Data
Center
Installation Guide

9 Installing Cables Outside Pre-fab. Modules

Issue 03 (2020-06-09)

Step 3

Remove the transparent cable protection panel from the power PDB busbar.

Step 4

Route the external input power cables into the power PDB through the cable holes at the
bottom, and route them out along the cable bridge above the cable holes.

Figure 9-2

Connecting input power cables for the power PDB

Step 5

Connect the cables by following the instructions in

A.1 Cable Installation Techniques

After connecting the cables, seal the two cable holes at the bottom of the power PDB using
waterproof sealing putty.

Step 6

Reinstall the transparent cable protection panel, and close the door of the power PDB.

----End

9.2 (Optional) Connecting Generator Start/Stop Cables
(ATS Input)

Prerequisites

Pre-fab. modules and external cable trays have been installed.

Summary of Contents for FusionModule1000A













































































































Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands

Huawei FusionModule1000A, Installation Manual

Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands