Huawei FusionModule1000A Installation Manual Download Page 70

Page: 70 / 108

FusionModule1000A40 Prefabricated All-in-One Data
Center
Installation Guide

8 Installing Devices Inside Pre-fab. Modules

Issue 03 (2020-06-09)

8.3.3 (Optional) Installing a Pad

Prerequisites

The pad to be installed has been obtained.

Context

Tool: Phillips screwdriver

Materials: pad and pad charging cable

Skill requirement: common technician

Procedure

Step 1

Adjust the feet at the bottom of the pad mounting support until they are in the same width as
the pad. Route the pad power cable through the cable hole in the pad mounting support and
then connect the cable to the pad.

Step 2

Adjust the feet in the upper part of the pad mounting support and clip the pad into the
mounting support.

Figure 8-16

Installing a pad

----End

Summary of Contents for FusionModule1000A













































































































Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands

Huawei FusionModule1000A, Installation Manual

Search results

Summary of Contents for FusionModule1000A

Reviews:

Related manuals for FusionModule1000A

Brands by name

Popular brands