Huawei FusionModule 1000A40 Maintenance Manual Download Page 24

Page: 24 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

3 Maintenance

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

Device

Operation

Check
Standard

Troubleshooting

All devices of
the fire
extinguisher
are free from
rust on the
exterior, and
the coating is
intact.

Repaint.

The lead seal
and safety
signs on
hand-operated
devices of the
fire cylinder
are intact.

Replace the electric control head.

Check the pressure
pointer of the fire
cylinder.

The pressure
pointer is in
the green zone.

Ask a fire engineer to check
whether the fire cylinder leaks
extinguishant. If leakage occurs, the
fire engineer charges the
extinguishant in the local charging
station.

Emergency
light

Disconnect the
power plug of the
emergency light.

The
emergency
light turns on.

Replace the emergency light.

3.2.6 Fire Extinguishing System (CE Tyco)

Table 3-7

Monthly maintenance checklist for the fire extinguishing system

Device

Operation

Check Standard

Maintenance Guide

Extinguisha
nt control
panel

Check indicators
on the
extinguishant
control panel.

The power indicator
turns on, and the
alarm indicator turns
off.

Replace the extinguishant
control panel.

Extinguisha
nt control
panel
batteries

Check the battery
terminals.

The wiring terminals
are in good
condition without
corrosion.

Clean the contaminated and
corroded terminals. Replace
the batteries with severely
corroded terminals for the fire
alarm control panel.

Fire
extinguisher

Check the
appearance of the
fire cylinder,
electrical actuator,
pneumatic switch,

All devices of the
fire extinguisher are
intact, free from
deformation and
mechanical damage.

Replace the fire cylinder. For
details about how to replace
other devices, contact Huawei
technical support.

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands