manualshive.com logo in svg

Huawei FusionModule 1000A40, Maintenance Manual, Page: 17 / 199

Share
Download
Huawei FusionModule 1000A40 Maintenance Manual Download Page 17

FusionModule1000A40 IT Solution 
Maintenance Guide (2016.05, AI Version) 

3 Maintenance 

 

Issue 04 (2018-01-05) 

Huawei Proprietary and Confidential                                     

Copyright © Huawei Technologies Co., Ltd. 

9 

 

Cate
gory 

Item 

Method 

Expected 
Result 

Troubleshooting 

The coverage of 
the camera is 
optimal. 

If the area covered by the 
camera is inappropriate, 
adjust the camera coverage 
by following the instructions 
in documents delivered with 
the camera. 

Access 
controller 
communic
ation 
status 

Check the door 
status list in the 
management 
system.   

All door status 
icons under the 
access controller 
blink.   

If a door status icon is 
dimmed (unavailable), check 
the access controller and 
network status. 

 

3.2 Monthly Maintenance 

3.2.1 Power Supply and Distribution System 

Table 3-2

 

Monthly maintenance checklist for the power supply and distribution system 

Item 

Method 

Expected 
Result 

Troubleshooting 

Luminance 
of the 
three-phase 
indicators 

Check the 
luminance of the 
three-phase 
indicators. 

The 
three-phase 
power 
indicators are 
steady on. 

Replace an indicator if it generates 
no or dim light. 

SPD 
indicator 
and SPD 
circuit 
breaker 
status 

Check the SPD 
indicator and SPD 
circuit breaker 
status. 

The SPD 
indicator is 
green.   

If an SPD indicator is red, replace 
the SPD in a PDC.. 

The SPD 
circuit breaker 
is switched on. 

If an SPD circuit breaker is 
switched to OFF, switch it to ON. 

Buttons on 
the PD510 
electricity 
meter panel 

Push any button on 
the PD510 
electricity meter 
panel. 

The PD510 
electricity 
meter LCD 
lights up and 
displays 
information 
properly. 

1.

 

If the LCD does not display 
information properly (no display 
or fuzzy), check whether the 
power cable is properly 
connected. 

2.

 

If the power cable is correctly 
connected, Replace the PD510 
electricity meter. 

Summary of Contents for FusionModule 1000A40








































































































































































































Reviews:

No comments