Huawei FusionModule 1000A40 Maintenance Manual Download Page 120

Page: 120 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

5 Components Replacement

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

112

Figure 5-37

Short-circuiting the pressure announciator

(1) Red and black cables to the pressure
announciator

(2) Cables to the fire alarm control
panel

----End

Follow-up Procedure

Dispose of the removed gas release indicator that is confirmed faulty.

5.4.4 Replacing an Indoor Fire Alarm Horn/Strobe (Standard)

Prerequisites

A spare fire alarm horn/strobe of the same model is available and functional.

Impact on the System

The fire extinguishing system stops working during the replacement.

Preparations

Tools: Phillips screwdriver, flat-head screwdriver, step ladder

Materials: spare fire alarm horn/strobe

Documents: fire extinguishing device layout diagram (standard)

Skill requirement: fire engineer

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands