Huawei FusionModule 1000A20 Maintenance Manual Download Page 35

Page: 35 / 86

FusionModule1000A20 Prefabricated All-in-One Data
Center
Maintenance Guide

4 Parts Replacement

Issue 01 (2019-07-15)

Parts Replacement

4.1 Replacing Components for the Power Supply and
Distribution System

4.1.1 Replacing AC-DC Power System Components



For details about how to replace components for the power supply and distribution system,
see the user manuals for the components.



During parts replacement, the system may need to be powered off. Take measures to
prevent device overheating.

Table 4-1

Replaceable components of the AC-DC power system

Item

Component

Reference Document

TP48400B-N20B3

Rectifier

TP48200B-N20B2 &
TP48200B-N20B3 &
TP48200B-L20B2 &
TP48400B-N20B3 &
TP48400B-L20B1
V500R002C00 Indoor
Power Supply User Manual

Monitoring module

AC surge protection module

Circuit breaker

User interface module
(UIM)

Solar supply unit (SSU)

DC-DC converter

Battery temperature sensor

TP48600B-N20B1

Rectifier

TP48600B-N20B1 User
Manual

Monitoring module

AC surge protection module

Summary of Contents for FusionModule 1000A20























































































Search results

Summary of Contents for FusionModule 1000A20

Reviews:

Huawei FusionModule 1000A20, Maintenance Manual, Page: 35 / 86

Search results

Summary of Contents for FusionModule 1000A20

Reviews: